Honeywell Valves

Product Details:

According EN 806-2 pressure reducing valves protect household water installations against excessive pressure from the supply. They can also be used for industrial or commercial applications within the range of their specification. By installing a pressure reducing valve, pressurisation damage is avoided and water consumption is reduced. The set pressure is also maintained constant, even when there is wide inlet pressure fluctuation. Reduction of the operating pressure and maintaining it at a constant level minimizes flow noise in the installation.

Features:

• Inlet pressure balancing – no influence on outletpressure by fluctuating inlet pressure
• Up to size 11/4" approved by LGA for low noise, Group 1without limitations
• The valve insert is of high quality synthetic material and can be fully exchanged
• The outlet pressure is set by turning the adjustmentknob
• The set pressure is directly indicated on the set pointscale
• The adjustment spring is not in contact with the drinking water
• Integral fine filter
• Also available without fittings
• Conforms to BSEN 1567
• All materials are UBA conform
• All materials are ACS approved

Setup requirements:

• Install in horizontal pipework with filter bowl downwards
• Install shut-off valves
• The device downstream should be protected by means of a safety valve (installed downstream of the pressure reducing valve).
• In these cases the delivery pressure of the pressure reducing valve shall be set to at least 20% below the response pressure of the pressure relief-valve according to EN 806-2
• The installation location should be protected against frost and be easily accessible–Pressure gauge can be read off easily–With clear filter bowl, degree of contamination can be easily seen–Simplified maintenance and cleaning
• Install downstream of the filter or strainer

Specifications:

Additional Information:

• Item Code: D06F

Product Details:

By keeping track of the market developments, we are involved in offering world class Two Way Threaded Valves. Our offered valve is fabricated using high quality raw material and advanced techniques at the vendors’ end. They are designed with high precision in order to meet the international quality standards. Widely appreciated among clients for their high tensile strength, extraordinary performance, robust construction and optimum efficiency, these valves are acknowledged among clients all across the nation.

 

Features:

• Bronze body with BSPT-threaded connections
• High close-off pressure rating, couple with 600Nm actuator (ML6420/ML7420)
• Low seat leakage rate (0.05 percent of KVS)
• Spring-loaded, self-adjusting packing
• Accurate positioning to ensure state of the art temperature control
• Sizes range from DN65 to DN80

Application:

• Hot water
• Chilled water
• Domestic Hot Water
• Steam

Product Details:

The BS-HWC4 Manual Butterfly Valves is designed for Chilled & Hot Water to be operated by Hand lever or Gear Box (BS-MWC4).

Features:

• Wide Size range (DN50...DN900)
• Operated by Lever or Gear Box.
• 90 deg opening/closing operation.
• Cast iron Body with powder coating.
• Epoxy Coated Ductile Iron disc.
• Wafer type Connection

Product Details:

Features:

• Wide Size range (DN50…DN300)
• Operated by Hand Wheel
• Cast iron Body
• S.S Disc

General:

• The Balancing Valves is designed for double regulating, control and shut off valve with built-in pressure drop measuring facility.

Outside Dimension:
Part Descriptions:

Product Details:

Product Details:

We offer high quality Solenoid Valve, which are designed to meet the industry requirements. Used as safety devices for storing tanks, containers, gas or vapor during transportation.

Features:

• Class A valve for control of gas consu-ming appliances.
• The VE....X series gas valves except VE....S series have a spring loaded val-ve disc, closed when de--energized.
• The VE....S series gas valves have a spring loaded valve disc, opened when de--energized.
• Incorporating time proven design con-cepts assuring reliability.
• All VE.... series gas valves have an in-ternal fine mesh screen.
• Two R1/4" connections for inlet pressu-re at each side of the electro magnetic gas valve.
• The VE....X 1... series gas valves have a wrench boss as well on inlet side as on outlet side for pipe fitting incorporated in the valve housing.
• The VE.... series gas valves may be as-sembled on the pipe linewith in plus or minus 90 degrees of the vertical axel.
• The VE....X 3... series gas valves (flange connection) have two (1/4") inlet pres-sure taps and two 1/4") outlet pressure taps at either side.
• The VE....X 3... and VE5...X 3... series gas valves have at inlet side two 1" ISO 7--1 connection taps.
• The VE....X 3... and VE5...X 3... series gas valves are equiped at both sides with mounting holes to adapt a pilot so-lenoid valve combination, to allow eit-her internal or external pilot gas. Futhermore these valves are equiped with two M6 mounting holes to adapt an A4020A electronic leak test control-ler (see dimensional drawing page 11).
• The VE ....B series gas valves have an adjustable flow rate regulator on top of the coil

Application:

• These series class A gas valves are used for control and regula-tion of gaseous fluids in gas power burners, atmospheric gas boilers, melting furnaces, incinerators and other gas consuming appliances.

Description:

• The VE series gas valves offer a series of functionalities: Gas valves, Normaly Closed, consisting of a direct ON/OFF operator for ope-ning/closing of the valve.
• Gas valves for use with Honeywell V4055, V4062 and V9055 fluid power actuators.
• Relief valves with or without position in-dication switch, Normaly Open, consi-sting of direct electric ON/OFF operator for opening/closing of the valve.
• The VE series gas valves are suitable for the control of gaseous fluids in gas con-suming appliances according to internati-onal standards.
• The VE series gas valves meet the class A specification according EN 161.
• The VE series gas valves cover a wide range of pipe sizes from 3/8" (DN 10) up to and including 3" (DN 80).
• The VE series gas valves have threaded connections from 3/8" (DN 10) up to and including 21/2" (DN 65).

Product Details:

The VC7900 Series Modulating Control Valves provide precision flow control of hot or chilled water in various heating and cooling applications. The VC hydronic valve consists of a valve body and replaceable characterized cartridge assembly. When used with a Honeywell VC7900 actuator, the valve provides proportional flow in modulating, diverting or mixing applications. They are designed to provide sinusoidal valve actuator travel, and therefore operate silently and resist water hammer. The VC7900 series valve actuator is used with any 0-10 Vdc or 2-10Vdc controller.

Accessories and Replacement Parts:

• 40007029-002: Wrench for removing VC cartridge
• VCZZ1100: 2-way characterized cartridge, unit pack
• VCZZ6100: 3-way characterized cartridge, unit pack

Specifications:

Product Details:

We have been successfully satisfying the diverse needs of our esteemed clients by providing a flawless gamut of Two Way Threaded Globe Valves. They are used to control steam, water and glycol solutions (up to 50 percent concentration) in heating or cooling HVAC application. Widely used in two-position and modulating control systems, they are not suitable for combustible gas service. These valves are widely renowned among clients for their significant high performance, optimum efficiency, easy operation and corrosion resistance.

 

Features:

• Red brass body with BSPT-threaded end connections
• Low seat leakage rate
• 50:1 range ability per VDI/VDE 2173
• Accurate positioning to ensure state of the art temperature control
• Bronze body with BSPT-threaded end connections.
• Low seat leakage rate (≤0.05 percent of Kvs).
• Spring-loaded, self-adjusting packing.
• Valve designs provide equal percentage flowcharacteristic for water and linear flow characteristic forsteam.
• Stainless steel stem and metal-to metal seats.

Application:

• Hot water
• Saturated steam
• Chilled water
• Domestic Hot Waterin Heating, Ventilating, Air Conditioning SystemsOpen Circuits

Specifications:

Additional Information:

• Item Code: V5011P

Product Details:

With the assistance of our team of professionals, we are offering Two Way Flanged Valves that are sourced from the most reliable vendors of the market. These valves are used for modulating control of hot or chilled water or steam in heating, ventilating & air conditioning systems and can be operated by electric linear actuators as ML6421, ML7421. The offered valves are manufactured using the finest grade raw material and sophisticated technology in compliance with the set industry standards at the vendors’ end. Robustness, low maintenance and durability are some of the features of our offered valves.

 

Features:

• Cast iron body with flanged end connections
• High Close-off Pressure Rating (1000kPa) & Low seat leakage rate
• Metal to metal seating for long life span
• Self adjusting packing
• Accurate positioning to ensure state of the art temperature control
• Directly coupled with electric actuators for easy mounting
• Approved according to DIN 32730

Installation:

• Water should meet VDI 2035 requirements.
• Do not install valve with stem below the horizontal.
• Fluid flow must correspond with the arrow direction on the valve body.
• The installation of a strainer is strongly recommended.

Specifications:

Additional Information:

• Item Code: V5088A

Product Details:

Features:

• Forged Brass Body
• Chrome Plated Ball
• Standard Port and Full Port Design

Dimension:

Product Details:

These three port mixing valves are used for modulating control of hot or chilled water in heating, ventilation and air conditioning systems and can be operated by electric linear actuators as ML6420/6425, ML7420/7425, M6421/7421 or by pneumatic actuators MP953.

Features:

• Cast iron body with flanged end connections
• Metal to metal seating for long life span
• Self adjusting packing

Merkmale:

• Graugussventil, geflanscht
• Metallsitze für lange Lebensdauer
• Federbelastete, selbstnachstellende Stopfbuchsen-packung aus PTFE-Manschetten
• Präzise Positionierung zur Gewährleistung einer ge-nauen Temperaturregelung
• Verwendbar mit elektrischen und pneumatischenAntrieben
• Konstanter Gesamtdurchfluss über den vollen Kegel-hub

Specifications:

Additional Information:

• Item Code: V5329A

Product Details:

These series class a Gas Valve are used for control and regulation of gaseous fluids in gas power burners, atmospheric gas boilers, melting furnaces, incinerators and other gas consuming appliances.

The VE series gas valves offer a series of functionalities:

• Gas valves, Normaly Closed, consisting of a direct On/Off operator for opening/closing of the valve
• Gas valves for use with Honeywell V4055, V4062 and V9055 fluid power actuators

Product Details:

The S245B and S245BH safety valves are direct loaded high performance safety valves with lifting device. They protect pressurized compressed air vessels (cylinders, tanks) against excessive pressure. S245B and S245BH safety valves are used for compressors and other industrial purposes.

Application:

• Compressed air
• Non-toxic, non-corrosive and non inflammable gases which may be discharged to atmosphere
• Not suitable for steam

Features:

• Sturdy metal construction
• Shakeproof lifting mechanism admitting no additional load
• Type S 245 B approved by VdTÜV for pressure range from0.5 - 30.0 bar and approved by ASME (American Societyof Mechanical Engineers) for pressure range 2.8 - 30.0 bar(41 - 435 PSI)
• Type S 245 BH approved by VdTÜV for pressure rangefrom 0.5 - 30.0 bar
• Types S 245 B / S245 BH certified to Pressure EquipmentDirective 97/23/EC, Reference No. CE 0035
• Set pressure adjustment at factory
• Set pressure settings possible between 0.5 and 30 bar insteps of 0.1 bar
• Low weight
• Reliable and proved

Installation Guidelines:

• Safety valves for compressed air shall be fitted in a verticalupwards pointing pipework or on top of a pressurizedcompressed air vessel.
• The connections through all pipe, fittings and nonreclosingpressure relief devices (if installed) between a pressurevessel and its safety valve shall have at least the area ofthe safety valve inlet.
• The characteristics of the upstream system shall be suchthat the pressure drop will not reduce the relieving capacitybelow that required or adversely affect the properoperation of the safety valve.
• The opening in the vessel wall shall be designed to provideunobstructed flow between the vessel and its safety valve.
• There shall be no intervening stop valves between thevessel and its safety valves.

Product Details:

We are offering Honeywell Check Valve to our client.

Additional Information:

• Item Code: BSC4-CWD-PN16

Water Flow Switch
Suitable for 1" to 6" size
Operating Pressure 10kgf/cm² (1000KPa)

Additional Information:

• Minimum Order Quantity: 1 Piece
• Delivery Time: Ex-stock